www.images-magazine.com NOVEMBER 2026 images 61 TIPS & TECHNIQUES Tony Palmer has been in the garment decoration industry for more than 30 years and is now an independent print consultant working closely with print shops across the globe to get the most from existing processes and techniques. He also co-hosts the popular screen printing podcast Chippy Tee! with Danny Donald of The Flippin Sweet Print Co. www.palmprintuk.com screens and was ready to press ‘Inlet Mode’ within four minutes. This ‘dance’ was one of the slickest pieces of print floor choreography I have seen in a long time. It is, in fact, the very epitome of what I try to instil in all my clients. Here it was working so efficiently that it was the main cause of my issue. There was nothing wrong. Loss of trust After my odd appreciation for this slick movement routine, I started talking to the main operator, a lady with 15 years’ experience whom, if cloning was legal, I would absolutely like to take a copy of and place in print shops around the world. A short discussion revealed that since the old machine was replaced with the new machine, the pre-registration system was no longer accurate. The skill level of this operator meant that the time taken was still at an industry-rare minimum, but where she used to trust the system, she had since reverted to visually aligning screens before printing. Now, this did cause some raised eyebrows with me. As I mentioned before, I am intimately familiar with this system and have seen the retrofit of the i-Image being used with these machines before too. My investigations took me to the screen room, and suspect number one – the CTS. Seeing the conversion, I pointed out that the best method of pre-reg must match exactly the method used at press. Here we had a small anomaly in the force being used to hold the screen in the clamping system. Luckily, we had a gifted technician on site and soon rigged up a device that perfectly matched the force used on press. This didn’t work. After performing calibration tests, I was still seeing anomalies in the setup accuracy. Datum difficulties To understand my eureka moment, we need to explain how Newman roller frames are held in the MHM clamping system. Static box-section aluminium frames are held using four female bushings attached to the frame at exact distances. Newmans use four male pins at varying distances. This variance is part of the very nature of Newman rollers; we simply cannot guarantee the distance between the pins down to the level of accuracy that matches the nylon bushings. The solution was an engineering one. The Newman frame holders on press, and subsequently on the CTS, were manufactured to have a master datum point on one side and an elongated slot to accept the differing distances on the other. If I haven’t lost you yet with the technical analysis, hold on, it gets better. My eureka moment appeared when I noticed that the CTS had the datum points at diagonal locations, top left and bottom right. This lined up perfectly with the older press that was located just outside the screen room. It was easy to just pop my head out of the electric sliding door of the stencil department and check that everything matched. While calibrating the new-to-them press that had just been installed, I noticed that this press had datum points on the right-hand side, top and bottom. Here it was, the anomaly I had been searching for. With different datum points on two presses, and opposing ones on the CTS, we could never achieve the accuracy that was enjoyed by the SP3000. This raised the question: why was the old SP3000 accurate and the new S-Type press not? Fresh set of eyes Luckily for me, the old press was still crated in the basement, ready to be shipped. After climbing and stumbling around the basement, I said the magic words, ‘Hey Siri, Lumos.’ It was revealed to me, in this basement of secrets, that way back in 1997 the Austrians made the presses with diagonal datum points as standard. I am not sure when the Austrian engineers decided to change to a righthand-side bias, but now I had a constant I could copy and paste across all points of contact. My visit did have a positive outcome, but perhaps the bigger lesson was that there didn’t need to be anything fundamentally wrong with the operation in the first place. The dance was already working. The people were good, the process was good, and the printer had simply learned to compensate for a system she could no longer completely trust. A series of equipment changes had quietly removed one common reference point. Here I was reminded that the value of a fresh set of eyes isn’t finding what’s broken; it’s spotting the one small inconsistency that everyone else has become very good at working around. I leave Slovenia confident in the knowledge that, as soon as the old screens have worked their way through this fast-moving system, I will, from a distance, achieve that ‘Wow’ moment I so crave. Sunset in Maribor, Slovenia A souvenir for Tony
RkJQdWJsaXNoZXIy MzY5NjY3